RF-Transmitter-Receiver-Pair-433-MHz----RXB6.jpg

RF Transmitter Receiver Pair 433 MHz - RXB6

Model No: WIR-00015

TK. 290.11

Quantity:

Category: RF

Supplier: Made in China

This pair consists of an RF transmitter and receiver. These can be interfaced with Encoder and Decoder ICs.

 

We have two different 433MHz RF modules: the RXB6 and the FS1000A. Both of them runs with the same code and user interface.


 

RXB6

FS1000A

Quality of reception

Very good

Good but not great

Transmitter Signal Noise

LOW

HIGH

Transmitter Current consumption

6.7mA

3.8mA

Range

 300m

100m

 

Buy FS1000A 433MHz modules from here.


Transmitter Specs:

  • Transmitter: JMR-TX1
  • Operating voltage: 3-12V
  • Operating frequency:433MHZ
  • Transmission distance:300-500m
  • Operating temperature  :-20℃~60℃
  • Dimensions:11*16*5.5mm
  • Input signal :TTL level
  • Modulation system :ASK
  • modulate rate:3KB/S
  • frequency stability:±75KHZ
  • Transmitted Power:≥10mw
  • Pins :4 

 

Receiver Specs:

  • Receiver:RXB6
  • Working voltage: 5.0VDC +0.5V
  • Working current: ≤2.5mA (5.0VDC)
  • Working principle: superheterodyne
  • Working method: OOK/ASK
  • Operating frequency: 433MHz



Question & Answer

Total 38 questions

Q: Hi, I need to know the dimension of this product. Questioned by amitapos, 23-May-2014

Tx-1.6 cm x 1.1 cm Rx-4.3 cm x 1.1 cm Answered by A.R, 01-Jun-2014 10:19 AM

Q: I need the pin-out setting and data-sheet of this... Questioned by Sayom_Shakib, 30-May-2014

Pinouts are clearly inscribed in its body and about datasheet, sorry. The supplier didn't give any. Answered by A.R, 29-Jun-2014 16:15 PM

Q: does it work with out antena. Questioned by piyash, 29-Jun-2014

Both the Transmitter and receiver have Antenna pins. Those can be used by grounding them if needed. Answered by A.R, 29-Jun-2014 16:14 PM

Q: What about it's transmitting distance? Questioned by Julfikar, 15-Jul-2014

300-500 m. Please check the specification section. Answered by A.R, 16-Jul-2014 15:19 PM

Q: I have tested this one with raw data (0 and 1 for blink) and able to receive on 5th floor roof, while transmitting from first floor ! While there is no transmission, receiver picks up garbage data, if no decoder used ! One thing to notice : The SMALL Unit is the Transmitter The LONG Unit is the Receiver here is the transmitter datasheet : http://www.jmrth.com/download.asp?n=TX1EN.pdf Questioned by suntop, 16-Aug-2014

Q: :'( unavailable? When will it be available again? pls hurry! There was another pair of wireless tx rx,where is it now? I was unable to find it :'( . What is the main difference between these two? I mean there must be reason why that was of low price,right? Questioned by Rakib.Ctg, 27-Sep-2014

We have this one http://www.techshopbd.com/product-categories/rf/640/rf-transmitter-receiver-pair-techshop-bangladesh. Both are different in size, range and number of pins. Answered by A.R, 28-Sep-2014 10:04 AM

Q: I am new in this kind of thing. I am sorry if it is not an appropriate question. Is it 2 channel RF Transmitter Receiver? Questioned by naeem_khan, 10-Oct-2014

1 channel. Answered by A.R, 11-Oct-2014 11:31 AM

Q: when are u going to import it ? please hurry... Questioned by Shabab, 26-Oct-2014

You can try this one. http://www.techshopbd.com/product-categories/rf/640/rf-transmitter-receiver-pair-techshop-bangladesh Answered by A.R, 26-Oct-2014 16:44 PM

link is not ok. chk it. Answered by atifmahbub, 31-Oct-2014 19:33 PM

It's working perfectly here. Please try again. Answered by A.R, 02-Nov-2014 10:20 AM

Q: can i able to use it as a voice transmitter and receiver . Questioned by mdrazu, 28-Jan-2015

Q: Hi there, I've bought 2sets of this product last week. This product requires an antenna to transmit and receive signals. Can anyone please let me know where can I get the antenna for this ? Or is there any other option to receive and transmit signals? Thanks Mushfiq Questioned by muushfiqq, 08-Feb-2015

Have you seen that the module already has a pin marked as 'Antenna'? That pin itself is an antenna. If you wanna use that, you just have to ground that pin, that's it. Answered by A.R, 08-Feb-2015 09:49 AM

Q: May i able to transfer voice data using this Questioned by mdrazu, 18-Feb-2015

Q: i have successfully done a LED on/off >>>but i don't know about address pins >>>without address pin i have done this >>>>>The Question is what is the benifit of the address pins >>>> Questioned by mdrazu, 18-Feb-2015

Q: আবার কবে স্টকে পাওয়া যাবে? Questioned by sayzar, 21-Mar-2015

Q: Can i Transmit audio data through this transmitter and receive by the Receiver? Questioned by shawan, 22-Mar-2015

Q: When no data is transmitted, the receiver receives Garbage. How to remove it ? Questioned by partho_sarkar, 31-Mar-2015

Are you grounding the 'Antenna' pin? Answered by A.R, 31-Mar-2015 10:05 AM

No. Answered by partho_sarkar, 03-Apr-2015 22:12 PM

Do I need to ground the Antenna Pin ? Answered by partho_sarkar, 03-Apr-2015 22:13 PM

Q: Can you please tell me the difference between this and https://www.techshopbd.com/product-categories/rf/1339/rf-transmitter-receiver-pair-433-mhz-techshop-bangladesh ? Questioned by muushfiqq, 20-Apr-2015

Sorry I made a mistake here. The url should be this : https://www.techshopbd.com/product-categories/rf/640/rf-transmitter-receiver-pair-techshop-bangladesh So I want to know the difference between RF Transmitter Receiver - Pair (433 MHz) Model : WIR-00015 and RF Transmitter Receiver - Pair Model : WIR-00003. Thanks Answered by muushfiqq, 20-Apr-2015 12:14 PM

Q: Is the receiver(RXB6) capable to receive multiple transmitter's(two or more JMR-TX-1) data? Questioned by amanullah.en, 29-Jul-2015

Yes. Answered by A.R, 30-Jul-2015 17:48 PM

Thanks :) Answered by amanullah.en, 01-Aug-2015 14:38 PM

Q: I guess the new products in stock are different. Can you give the datasheet of the new product.. Questioned by shparvez001, 05-Sep-2015

post in wrong page Answered by shparvez001, 05-Sep-2015 02:05 AM

Q: What is about it's baud rate . Thank You! Questioned by naasifn, 21-Oct-2015

9600 Answered by A.R, 25-Oct-2015 11:35 AM

Thank You!! Answered by naasifn, 25-Oct-2015 13:04 PM

Q: can i use it for laptop? Questioned by muntasirr611, 14-Jan-2016

Q: can i use it for laptop? Questioned by muntasirr611, 14-Jan-2016

Q: can i use it audio sending and reviving system? Questioned by nauroj, 14-Jun-2016

Sorry! It can be used only for bit-wise data communication. If you want, you can use Bluetooth module, we have such module that is able to transmit audio signal. Please follow the link bellow: [Link: https://www.techshopbd.com/product-categories/bluetooth/1760/rn-52-bluetooth-audio-module-techshop-bangladesh] Answered by FAHIM_REAZA, 15-Jun-2016 11:36 AM

Q: i want the transmitter and receiver data sheet .. can you please give me link.. Questioned by Jahedulislam, 20-Jun-2016

Follow the "Documents" tab. Answered by FAHIM_REAZA, 20-Jun-2016 10:06 AM

Q: 1. i have found a datasheet of tx unit, that says absolute max voltage is 6v, on the other hand you've written 3-12v. http://www.geelmed.com/documents/products/producto_000000110DOC.pdf?d=1309807550 2. i have found in a website that receiver unit can have a 17.3cm single core copper wire as antenna, does tx unit need one? http://www.nemcon.nl/blog2/2015/07/aa 3. one of the above comment says to ground the antenna pin, is it ok or not. 4. can i transmit audio? Questioned by Hasnat Jamil, 06-Sep-2016

Dear customer, all of your answer is given bellow: ------------------------------------------------------------------- Ans_1: For Transmitter, this is recommended by us to use 3V(min) to 12V(max). 12V is used to ensure maximum data transmission. Ans_2: Yes. You have to use 17.3cm antenna in both the Transmitter and Receiver units. Ans_3: Please don't connect this antenna pin to GND. Ans_4: This Trans-receiver is not capable to audio-video data transmission. You can use it for just only bit-wise (Logical 1 or 0) data transmission. Thanks for with us. Answered by FAHIM_REAZA, 06-Sep-2016 10:10 AM

thanks... Answered by Hasnat Jamil, 06-Sep-2016 17:06 PM

Q: URGENT QUESTION: DO THESE MODULES HAVE ICs INTEGRATED WITH IT? BECAUSE I HAVE JUST FOUND ANOTHER MODULE WHICH HAS IC HT12D AND HT12E INTEGRATED.IF IT DOESN'T HAVE THE IC INTEGRATED WITH IT,THEN WILL IT WORK AS THE ONE WHICH HAS INTEGRATED IC?? sorry for this lame question. Questioned by Navidahmed, 14-Oct-2016

This one is without encoder, decoder. The user has to interface them. Answered by A.R, 16-Oct-2016 09:43 AM

thanku... another ques: does arduino has v regulator built in...?? Answered by Navidahmed, 16-Oct-2016 22:35 PM

have** Answered by Navidahmed, 16-Oct-2016 22:35 PM

Q: an urgent question: can i use the transmitter and receiver just with arduino?? If i dont use IC with it, will it work just with the arduino, coz arduino has built in IC ??? where can i get the antenna from?? Please anyone answer. Questioned by Navidahmed, 30-Oct-2016

You can. Please get some idea from here. http://www.instructables.com/id/RF-315433-MHz-Transmitter-receiver-Module-and-Ardu/. If you solder a copper wire or jumper with the 'ANT' pin, it will work as an antenna. Answered by A.R, 31-Oct-2016 09:51 AM

thank you bro I need to talk to you urgently...aikhane formally comment e kotha bolar theke mayb email e jodi ektu help korte parten bhai, onek upokar hoito....apni chaile apnake email korbo Answered by Navidahmed, 31-Oct-2016 18:47 PM

Please mail to technicalsupport@techshopbd.com Answered by A.R, 31-Oct-2016 19:07 PM

Q: availabl kobe hobe.? Questioned by Simonn, 03-Nov-2016

Q: What about it's transmitting distance? Questioned by sumonahmed, 20-Nov-2016

from 1 building to another building..... Answered by sumonahmed, 20-Nov-2016 10:30 AM

Transmission distance:300-500m. Kindly see the given specification and documents. It's written there. Answered by A.R, 20-Nov-2016 12:53 PM

Q: Can i use it to make a fm radio transmitter Questioned by inductor, 27-Jan-2017

Q: Can i use it to make a fm radio transmitter Questioned by inductor, 27-Jan-2017

Possible but it's not practical. Answered by A.R, 28-Jan-2017 10:07 AM

Q: Do u have any module which can be helpful for my project? Questioned by inductor, 28-Jan-2017

Q: please stock this product Questioned by muradshakil, 04-Mar-2017

It will be available soon. Please click on 'Notify me W/A' beside the product image. You will get an sms as soon as it is available. Answered by A.R, 05-Mar-2017 17:18 PM

Q: please stock this product Reply Questioned by muradshakil, 04-Mar-2017

Q: how many channels ? Questioned by zaheed, 21-Apr-2017

Q: Hi are you Sure it work in 300-500meter..how long need antiner for tx & rx.. Questioned by sumonahmed, 29-Apr-2017

Q: এই ট্রান্সমিটার থেকে কিছু ট্রন্সমিট করে মোবাইল রেডিও কিংবা রেডিও তে শোনা যাবে নাকি ? আর 433 Mhz বলতে আসলে কি বুঝানো হচ্ছে। নরমালি 87-105 MHz এ এটা কাজ করবে কি ?? Questioned by meghvela, 22-May-2017

যাবে না। এটা রিমোর্ট কন্ট্রোল বানানোর জন্য। ৪৩৩ মেগাহার্জ মানে এর ট্রান্সমিটার ৪৩৩ মেগাহার্জ ক্যারিয়ার সিগন্যাল উপন্ন করে। Answered by A.R, 23-May-2017 10:48 AM

Q: 433mhz violating btrc rules and regulations. Isn't it? Questioned by imranhert, 22-Dec-2017

In short range it is not a problem. Range of this tx and rx module is 100m only. Answered by A.R, 23-Dec-2017 09:43 AM

Q: Can I use it without the UART interface? Questioned by nargisakhter, 08-May-2019

UART? This pair has nothing to do with UART. Answered by A.R, 08-May-2019 15:47 PM

Reviews & Ratings

0 Ratings / 0 Reviews

[0]

[0]

[0]

[0]

[0]

icon

Help: 09678110110

09.00am - 08.00pm (7 days a week)

icon

Pay cash on delivery

Pay cash at your doorstep

icon

Service

All over Bangladesh

icon

Warranty and Replacement

Up to 1 Year