L293D Dual DC Motor Controller

Model No: ROB-00165

TK. 379.97

Availability: In stock


Category: Motor Driver

Supplier: Techshop Bangladesh

L293D Dual DC Motor Controller Red এটি একটি মোটর ড্রাইভার। যা তৈরি করা হয়েছে একটি L293D Motor Driver আইসি ব্যবহার করে। এই কন্ট্রোলার ব্যবহার করে একসাথে দুটি ডিসি মোটর খুব সহজেই ড্রাইভ করা যাবে। তবে একটা বিষয় লক্ষ রাখতে হবে যে, এর কারন্ট ও ভোল্টেজ রেটিং। যদি কেউ L293D Dual DC Motor Controller Red এর রেটিং এর অধিক রেটিং সম্পন্ন মোটর ব্যবহার করতে চায় তাহলে এটি কাজ করবে না।



Operating Voltage: 7V-15V

Motor Voltage Selection = VS (5V or Vin)

DPDT Power Switch

DPTD Dual Motor Enable Switch

Power Input Terminal 3 Pin (VIN – GND – 5V)

Signal Input Terminal Pin (IN1, IN2, IN3 & IN4)

PWM Input Terminal (ENA & ENB)

Output Terminal (Motor A & Motor B)

4 Pins 5V Bus  for another boards.

4 Pins & 2 Pins GND Bus  for another boards.




L293D Dual DC Motor Controller কিভাবে ব্যবহার করবো?

Operating Voltage: 7V-15V

Motor Voltage Selection = VS (5V or Vin)

DPDT Power Switch

DPTD Dual Motor Enable Switch

Power Input Terminal 3 Pin (VIN – GND – 5V)

Signal Input Terminal Pin (IN1, IN2, IN3 & IN4)

PWM Input Terminal (ENA & ENB)

Output Terminal (Motor A & Motor B)

4 Pins 5V Bus  for another boards.

4 Pins & 2 Pins GND Bus  for another boards.


Question & Answer

Total 32 questions

Q: is it compitable with gear motors?? Questioned by fizur2, 14-Jan-2015

Yes. Answered by A.R, 14-Jan-2015 16:11 PM

Q: Can I used it in my line follower bot for better performance? Questioned by tusheraziz, 17-Jan-2015

We don't know what is meant by 'better performance'. But yes, this one is pretty convenient for line followers. Answered by A.R, 17-Jan-2015 11:40 AM

Q: I am a newbie. I have one of this from your shop. Is it enough to drive two 6v dc motors? Do the input pins take analog values(if takes what is the max value)? Questioned by mahbub2012, 04-Feb-2015

Input pins either take logic high or logic low. 6V motors can be driven pretty smoothly with this. Please see the datasheet of L293D. Answered by A.R, 05-Feb-2015 10:47 AM

Q: Does the logical part needs to be connected with any power source when i am already giving vcc 12V. Questioned by Rashed_ali10, 05-Feb-2015

Q: why enA & enB attached with 5v pin? Questioned by AididAlam, 11-Mar-2015

Kindly see that datasheet of L293D. Until and unless you make Enable pins high, the motors will never rotate. If you want any motor to stop forever, disconnect the enable pin from 5V. Answered by A.R, 12-Mar-2015 10:38 AM

Q: Can I run two 12V DC motors with this? Questioned by harry99901, 28-Apr-2015

It depends on the current rating of your motor. Answered by A.R, 04-May-2015 12:30 PM

Q: Can I control the speed of the motor? and how? Questioned by protanvir, 09-May-2015

By PWM. Answered by A.R, 10-May-2015 09:40 AM

Q: ata die ki motor chalano jabe kina? Questioned by Dana.Rifat, 09-Jun-2015

Q: Can i Connect it to Arduino? Questioned by Akmal101, 11-Jun-2015

Yes.Of course. Answered by A.R, 11-Jun-2015 17:51 PM

How should I Connect it with Arduino Mega2560?? Answered by amantu, 21-Sep-2015 13:13 PM

the In 1 and In 2 pins are for controlling motor 1, while the In 3 and In 4 pins are for controlling motor 2. Connect these 4 pins to any digital output pin of Arduino... e.g. Digital pins 5,6,7,8 of Arduino or as you wish... Answered by swapnilsayansaha, 21-Sep-2015 19:14 PM

If In 1 is high, motor 1 runs forward (you can specify speed by sending an analog output).. If In 2 is high, motor 1 runs backward... Similar for motor 2 as well..... Answered by swapnilsayansaha, 21-Sep-2015 19:15 PM

Q: via ami 26-07-15 e L293D Dual DC Motor Controller kinci but kaj kore na..........Order Information #115062 Questioned by abubakar, 02-Aug-2015

Make sure that you are using it correctly. If still no luck, please send us the product back along with a copy of your invoice. We will check that and give you a possible solution. Sorry for this inconvenience. Answered by A.R, 02-Aug-2015 09:58 AM

Q: ami ki ota nia 05-08-15 day e aste pari... Questioned by abubakar, 02-Aug-2015

Q: Can I run my HDD motor with it ? Questioned by Tusharjee6, 04-Oct-2015

Depends on the current rating of the motor. Motor's current rating must not be greater than that on L293D. Answered by A.R, 04-Oct-2015 09:50 AM

Q: i am new in your site,Can you give me Details about it.. Questioned by Ahmedsihab, 14-Oct-2015

Details are already given on top of the site. Please see. Answered by A.R, 14-Oct-2015 12:19 PM

Q: video tutorial e l293d er 5V pin e kunu connection dayni... 5V connection na dile ki kunu problem chara motor drive kora jabe??? Questioned by wakil.pabel, 17-Oct-2015

৫ ভোল্ট এর জন্য কানেকটর রাখা হয়েছে প্রধাণত বোর্ড‌টা টেস্টিং এর জন্য। ভিডিওতে ব্যবহৃত মোটর ছিল ৬ ভোল্ট। যা সরবরাহ করা হয়েছে Vin পিনকে ব্যটারির সাথে সংযুক্ত করে। এবং কোনো সমস্যা ছাড়াই যে রোবট চলেছে তা-ও দেখা গেছে ভিডিওতে। Answered by A.R, 18-Oct-2015 10:00 AM

Q: can i get the circuit diagram of this motor controller module....i want to make one...can u plz give me the diagram???? Questioned by farhat, 24-Nov-2015

No. It's against our policy. Answered by A.R, 25-Nov-2015 09:34 AM

Q: In this motor driver, Which pins are used as PWM-Pulse Width Modulation? Questioned by mkannan22, 28-Apr-2016

This "L293D Dual DC Motor Controller" has two pin named "ENA" and "ENB" which is initially shorted with 5V via two computer jumpers. If you want to use PWM signal, please disconnect the "Computer Jumper" (Just un-plug it) and send the PWM Signal to this ENA and ENB pins. Answered by FAHIM_REAZA, 02-May-2016 12:09 PM

Q: i want to know how much votage can take vin pin.. when i try to drive motor i dont get satisfied speed . . Questioned by edtmamun, 03-Jun-2016

Vin must be greater than 7V and upto 15V maximum. Answered by FAHIM_REAZA, 05-Jun-2016 18:16 PM

Q: Its my personal opinion, I prefer using the L298N motor driver circuit . Questioned by ShafinRubaer, 13-Oct-2016

Q: ami ki 4 ta gear motor connect korte parbo 1 ta motor driver a? r jonno ki 2 ta motor driver lagbe? Questioned by hhshovon, 13-Dec-2016

If you connect each two motors in parallel, you can. Answered by A.R, 14-Dec-2016 10:25 AM

tnx for reply. In this case, ami ki 2 motors r arduino code use korte parbo or amake 4 motor r jonno different code korte hobe??? Answered by hhshovon, 14-Dec-2016 19:05 PM

Q: Can i place it over arduino? Can this be used for making bluetooth controolled robot Questioned by waleey, 02-Jan-2017

No. This is not shield. So it can't be placed over arduino. You must use jumper wires to connect it with arduino. For DC motor controlling purposes including bluetooth controlled robot, it can be used. Answered by A.R, 02-Jan-2017 09:45 AM

Q: how can i setup the RF Transmitter Receiver - Pair (Model : WIR-00003) with this? Questioned by subject17, 24-Feb-2017

It's upto you. You have to send signal from the transmitter, catch it with the receiver and the received signal should go to the input pins of the motor driver. You should use microcontroller or arduino for this purpose. Answered by A.R, 25-Feb-2017 09:57 AM

Q: What about the current rating ? Questioned by tamzid73, 06-Mar-2017

600mA per channel. Answered by A.R, 07-Mar-2017 09:45 AM

Q: Is it available now? its urgent.u guys message me that its available...but its showing out of stock. how can i order it? Questioned by maliha_tabassum, 11-Mar-2017

Q: Can I connect arduino uno with it? Questioned by rinipakhe11, 06-May-2017

Yes. Why not? Answered by A.R, 07-May-2017 10:26 AM

Q: Ami robotics bishoya notun. Bortomane acta obstacle avoiding robot banate chachi. Ai robot toirite L293D motor drive shield dorkar. Ar poriborte apnader ai controllerta ki baboher korte parbo? Parle kibhabe please actoo bolun. Questioned by rinipakhe11, 07-May-2017

আমাদের কাজ তো এইখানে কোডিং শেখানো না, ভাই। ওটার জন্য ওয়ার্কশপ আছে। আমাদের অবস্ট্যাকল এভয়েডারের কিটেও এই মডিউল ব্যবহার করা হয়েছে। অবশ্যই এটা ব্যবহার করা যাবে।অবস্ট্যাকলের উপর একটা ভিডিও করার ইচ্ছা আছে লাইন ফলোয়ারের মতো। উপর মহল থেকে পারমিশন পেলে করে ফেলব। Answered by A.R, 10-May-2017 12:18 PM

It is a good idea. Answered by rinipakhe11, 10-May-2017 13:17 PM

Q: Please answer. Questioned by rinipakhe11, 09-May-2017

Q: আমি আপনাদের ভেকাম পাম্প কিনেছি এবং এটার স্পিড কন্ট্রল করতে চাই কিভাবে করবো? যদি এটা দিয়ে হয় তাহলে আমাকে জানালে ভালো হয় কারন আমি এবিষয়ে এতটা অভিজ্ঞ নয় তবুও গবেষনা কাজে ব্যাবহার করতে চাই, আর যদি সফল হতে পারি তবে ইনশাল্লাহ আপনাদের হাজারটা পন্য দিয়েও কুলোতে পারবেন বলে মনে হয় না, আপনার সাহায্য কামনা করি ৷ Questioned by helal888, 23-Jun-2017

Q: unfortunately i have supplied more than 15 v to the VCC pin, now my VCC pin is not working. i have checked the IC but its working. please how can i fixed this problem ? Questioned by sadrultoaha, 21-Aug-2017

Q: Hello, I bought this controller from you but now I am facing some problems for operating it. I have checked both datasheet and video tutorial. But it dd not help much. Please help me. Thank you. Questioned by Tashriqu_Ahmed, 17-Nov-2017

Hello, what is the problem? Answered by A.R, 19-Nov-2017 09:33 AM

Q: i brought this motor driver days ago but today was trying to0 build a obstacle avoiding robot . but now the do not work what would i do? Questioned by Iftiking, 08-Feb-2018

This is quite unusual because we always sell our own branded products after testing. Please disconnect the driver from your setup and check that separately. Also, If still the problem persists, let us know. Answered by A.R, 08-Feb-2018 17:33 PM

Q: এটা কি 5volt পাওয়ার ব্যাংক দিয়ে চালানো যাবে? Questioned by ashraful_92, 15-Oct-2018

যাবে। Answered by A.R, 15-Oct-2018 09:37 AM

Q: when it will available again?? Questioned by shafeeadnan, 26-Jan-2019

We no longer want to produce it. We are selling this now. https://www.techshopbd.com/product-categories/robotics/3033/l293d-dual-dc-motor-controller-high-quality-techshop-bangladesh Answered by A.R, 27-Jan-2019 09:51 AM

Reviews & Ratings

0 Ratings / 0 Reviews







Help: 09678110110

09.00am - 08.00pm (7 days a week)


Pay cash on delivery

Pay cash at your doorstep



All over Bangladesh


Warranty and Replacement

Up to 1 Year